Snipaste_2021-11-01_17-51-43.png

激光刀具测量仪可测量外径0.3-30mm,装夹方式陶瓷V型结构, 装夹柄径3-30mm, 测量仪直径线性精度0.002mm,重复性0.0001mm,标定后直径测量精度≤0.01mm。配备专业测量控制软件,标准机型可实现半自动测量,可非标订制全自动测量。可测量产品:标准铣刀,多刃刀具(6-16),棒材,微钻,高精度细长插芯轴等; 可测量项目 刀具:最大刃径,最小刃径,平均刃径,刃径跳动,同时可自动描绘出刃径高度变化曲线图;圆轴/棒材:最大直径,最小径,平均直径,真圆度,同时可自动描绘出真圆度变化曲线图, P17曲线图,该曲线图显示刀刃最高点的变化量

 

Outer diameter measure range is 0.3-30mm, clamping mode ceramic v-shaped structure, clamping shank diameter 3-30mm, diameter measuring linear accuracy 0.0015mm, repeatability 0,00015mm, after calibration diameter measuring accuracy ≤0.0003mm. Configured with professional measurement control software, standard models can achieve semi-automatic measurement, also can be customized to be full-automatic measurement. Measurable product: Standard milling cutter, multiple-cutting-edge tool (6-16), bar, micro-drill, high precision slender mandrel, etc. Measurable item, cutter: max/min/average value of blade-edge diameter, beating value of blade-edge, meanwhile the curve of blade diameter height change can be drawn automatically; circular shaft/bar: max/min/average value of diameter, roundness, meanwhile the curve of roundness can be automatically drawn. For example, the P17 curve

 

该曲线图显示刀刃最高点的变化量,此高度为刀刃最高点处于镭射光幕的位置高度,上图可以看出四个刀刃直径不在一个高度内,相差大约为8.8105-8.8055=0.005mm;从该曲线还可以看出看条刀刃的高低状况

The curve shows the changes in the highest point of the blade, this is the highest point of the blade edge at the position of the laser light curtain. Above figure shows that the diameter of the four blades is not within one height, the difference is approximately 8.8105-8.8055=0.005mm. Through the curve, we can also see the low-high status of the blades.

  

激光刀具测量仪一键测量棒材

圆棒测量,度变化量模拟圆度曲线图,X,Y轴单位是μ,可以看到360度的圆度微观变化

One-click measuring bar

Circular rod measurement, degree variation simulates roundness curves, axis units of X,Y are μ, this can show 360 degrees of roundness micro changes.

 

激光刀具测量仪一键测量铣刀

转动测量铣刀跳动,最大直径,最小直径,平均直径;同时自动描绘出刀刃外径的曲线图,曲线局部放大,可以从曲线图微观分析刀刃各刃的高低状况。

One-click measuring cutter

Measure run-out of milling cutter when rotation, max/min/average diameter; synchronously it automatically draws the curve of the outside diameter of the blade, the low-high status of each blade can be analyzed microscopically from the curve via local zoom.

激光刀具测量仪测量产品

图片关键词

图片关键词

  • 类型 : 刀具检测仪